turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Navigation
- Simcenter
- Forums
- Blogs
- Knowledge Bases

- Siemens PLM Community
- Simcenter
- CAE Simulation - Simcenter 3D Forum
- Can NX include mass transport into flow simulation...

Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

10-23-2013 07:27 PM

As stated in the Subject field, can the simulation results include pressure, velocities, temperature, AND mass fraction?

Solved! Go to Solution.

3 REPLIES

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

10-27-2013 03:08 PM

Hello!,

In NX Advanced Flow in addition to the mass, momentum, and energy equations, NX Flow solves general scalar equations to manage **mass fractions** where you can:

- Model a gas-gas mixture that contains miscible species, such as carbon monoxide in air using the
**Homogeneous Gas Mixture**modeling object. - Also you can use the Tracer Fluid modeling object in a flow that contains miscible species where the main fluid properties are not affected by the species, such as a smoke in air.
- And finally the NX FLOW solver can model humidity with a general scalar equation. It traces the movement of water vapor through the fluid domain, updating the density (r), specific heat at constant pressure (Cp), thermal conductivity (k), and dynamic viscosity (μ) at each iteration.

The workflow using the **Homogeneous Gas Mixture** is the following:

1. Create a Homogeneous Gas Mixture modeling object.

- The name you use for the material is used to name the corresponding concentration result set in post processing.
- You need to specify the molecular diffusion coefficients and turbulent Schmidt numbers for gases 2 to 5.

2. Define a gas mixture in a 3D mesh collector or a Fluid Domain simulation object.

3. (Optional) Specify initial or ambient conditions for a fluid volume with a Homogeneous Gas Mixture material.

- The
**mass fractions**are defined for all gasses, including the primary gas.

4. (Optional) Define mixture contents in an inlet boundary condition.

- You must use an External Conditions modeling object whenever you use a Homogeneous Gas Mixture modeling object in a flow boundary condition.

5. (Optional) Modify global ambient or initial conditions to model mixtures.

- You set the
**mass fractions**for all ambient gases on the Ambient Conditions tab of the Solution dialog box. - You set the initial mass fractions for all gases on the Initial Conditions tab of the Solution dialog box.

6. Add mixture result sets, solve, and view mixture results.

- Select the Humidity and Mixtures check box on the Results Option tab of the Solution dialog box.
- In the Post Processing Navigator, there are result nodes for each species of the mixture except the primary gas.
- The result nodes are named GasName_M#G# — Element-Nodal where GasName is the name of the fluid material you set in the Fluid Material dialog box, M# represents the number of Homogeneous Gas Mixture modeling object and G# represents the specific gas in the mixture.

Best regards,

Blas.

Blas Molero Hidalgo, Ingeniero Industrial, Director

IBERISA • 48004 BILBAO (SPAIN)

WEB: http://www.iberisa.com

Blog Femap-NX Nastran: http://iberisa.wordpress.com/

IBERISA • 48004 BILBAO (SPAIN)

WEB: http://www.iberisa.com

Blog Femap-NX Nastran: http://iberisa.wordpress.com/

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

10-28-2013 02:23 PM

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

10-29-2013 02:29 PM

Hello!,

OK, if you find my post helpful, and it answers your question, please mark it as an "* Accepted Solution*" -- thanks!.

Best regards,

Blas.

Blas Molero Hidalgo, Ingeniero Industrial, Director

IBERISA • 48004 BILBAO (SPAIN)

WEB: http://www.iberisa.com

Blog Femap-NX Nastran: http://iberisa.wordpress.com/

IBERISA • 48004 BILBAO (SPAIN)

WEB: http://www.iberisa.com

Blog Femap-NX Nastran: http://iberisa.wordpress.com/

Follow Siemens PLM Software

© 2018 Siemens Product Lifecycle Management Software Inc