Turn on suggestions

Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Navigation
- Simcenter
- Forums
- Blogs
- Knowledge Bases

- Siemens PLM Community
- Simcenter
- CAE Simulation - Simcenter 3D Forum
- Re: Random Fatigue from Acceleration PSD

Options

- Start Article
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

07-28-2017 07:55 PM

Hi all!

I have a cantilevered beam with the fixed end subjected to an enforced acceleration with a determined PSD.

I would like to run a random fatigue analysis in Virtual.Lab. How should I constraint the beam model in the modal analysis that I must submit to Virtual.Lab for the analysis?

In my analysis, I set one end of beam fixed for the computation of normal modes. However the fatigue damage computed by Virtual.Lab is really far from the analytical solution that I took from the Steinberg book for reference.

Is Virtual.Lab capable of vibration fatigue analysis with an enforced acceleration psd?

Solved! Go to Solution.

- Tags:
- psd

Labels:

4 REPLIES 4

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

07-31-2017 09:42 AM

Dear Hen,

it is possible to use Random Fatigue with acceleration loads, but there are numerical constraints when it comes to rigid body movements (i.e. the frequency of the loading being below the first eigen mode of the structure). In this case using acceletartion PSDs the numerical errors for low frequencies behave like 1/f^4.

Therefore we recommend to use in these cases a large mass approach. I.e. Add a large mass at the load application point and apply forces (using F=m a). Here the errors behave only like 1/f and you get good results for the local stresses and therefore the local damages.

Hope this helps

Michael

Dr.Michael Hack

Business Product Line Manager

Durability Simulation

Business Product Line Manager

Durability Simulation

Re: Random Fatigue from Acceleration PSD

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

07-31-2017 05:07 PM - edited 07-31-2017 05:08 PM

Thank you for your enlightening comment Sir!

The problem is that the beam excitation is a costant PSD acceleration of 3 g^2/Hz (from zero to 2000 Hz) and I have no idea how to convert this PSD acceleration to a force PSD for the large Mass approach.

Beside, the point of excitation for the enforced acceleration is the fixed end of the cantileverd beam and if I apply a PSD force to this fixed end I get zero MPFs and zero stresses.

The modal analysis submitted to Virtual.Lab is performed with one beam end fixed and the other one free.

Highlighted

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

08-01-2017 03:18 AM - edited 08-01-2017 03:22 AM

Dear Hen,

seems your application is indeed having the problems at low frequencies.

For the question on converting acceleration PSD to Force PSD: Multiply by the square of the large mass (As F=m times a) and the load is quadratic in the PSD, i.e. 3 g^2 m^2 [N^2/Hz]. The large mass model is a free free model.

BR

Michael

Dr.Michael Hack

Business Product Line Manager

Durability Simulation

Business Product Line Manager

Durability Simulation

Re: Random Fatigue from Acceleration PSD

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

10-28-2017 11:42 AM

Thank you Mr. Hack, now everything works fine.

Follow Siemens PLM Software

© 2019 Siemens Product Lifecycle Management Software Inc