Cancel
Showing results for 
Search instead for 
Did you mean: 

Nx Asking for Blank defination every time,,,why??????

Valued Contributor
Valued Contributor

Hi 

I have created a tool path on a very simple part for practice. I defined Blank and workpiece geometry correctly in operation nevegator geometry but when i try to verify my tool path with 3D Dynamic option . Nx always ask me to define Blank. Why??

I know its a very simple question but i expect from you guys that some may help me in resolving this issue.

Blank1.JPGBlank 2.JPG

7 REPLIES 7

Re: Nx Asking for Blank defination every time,,,why??????

Solution Partner Phenom Solution Partner Phenom
Solution Partner Phenom

Put your operations into the workpiece.

You have them on the same level with workpiece in the MCS and they dont see workpiece.

---------------------------------------------
#♫ PB, 5ax, itnc, nx, vericut ♫ #

Re: Nx Asking for Blank defination every time,,,why??????

Valued Contributor
Valued Contributor

@Juraj

I have already put my both operations under the workpiece as seen clearly in the screen shot(Already Attached),but getting same result.

Re: Nx Asking for Blank defination every time,,,why??????

Gears Esteemed Contributor Gears Esteemed Contributor
Gears Esteemed Contributor

Not below the workpiece, but inside of it, so that they are children of it.

Stefan Pendl, Systemmanager CAx, HAIDLMAIR GmbH
Production: NX12.0.2, VERICUT 8.2, FBM, MRL 3.1.7 | TcUA 10.1 MP7 Patch 0 (10.1.7.0) | TcVis 11.4
Development: C (ITK), .NET, Tcl/Tk Testing: NX (1876) | AWC 3.4 Preparing: -

Employees of the customers, together we are strong Smiley Wink
How to Get the Most from Your Signature in the Community
NX Customization - Best Practice Guide

Re: Nx Asking for Blank defination every time,,,why??????

Solution Partner Phenom Solution Partner Phenom
Solution Partner Phenom

@AaghaFarhan

 

Snímka.JPG

 

Snímka2.JPG

 

 

 

---------------------------------------------
#♫ PB, 5ax, itnc, nx, vericut ♫ #

Re: Nx Asking for Blank defination every time,,,why??????

Valued Contributor
Valued Contributor

@Juraj 

Check this please , i think i have done this already as you instructed.ssssss.JPG

Highlighted

Re: Nx Asking for Blank defination every time,,,why??????

Valued Contributor
Valued Contributor

Thank you @Juraj and @Stefan_Pendl

I got the point where i was making mistake,issue is resolved

Thank you

Re: Nx Asking for Blank defination every time,,,why??????

Gears Esteemed Contributor Gears Esteemed Contributor
Gears Esteemed Contributor

For others to make things clear, the display of the operation navigator and the dependencies pane must look as shown in the image below.Workpiece_used.PNGWorkpiece used by Operations

Hope this helps.

Stefan Pendl, Systemmanager CAx, HAIDLMAIR GmbH
Production: NX12.0.2, VERICUT 8.2, FBM, MRL 3.1.7 | TcUA 10.1 MP7 Patch 0 (10.1.7.0) | TcVis 11.4
Development: C (ITK), .NET, Tcl/Tk Testing: NX (1876) | AWC 3.4 Preparing: -

Employees of the customers, together we are strong Smiley Wink
How to Get the Most from Your Signature in the Community
NX Customization - Best Practice Guide

Learn online





Solution Information