Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for

- Navigation
- Solid Edge
- Forums
- Blogs
- Knowledge Bases
- Contests
- Groups

- Siemens PLM Community
- Solid Edge
- Solid Edge Forum
- Bolt Hole circle

Options

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page

N/A

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

12-15-2008 05:08 AM

Rick

I'm a bit late replying.

Many thanks for your comprehensive responses.

I understand the formula relationships a little.

I drew a bolt circle using the circular function.

I had to ungroup these to be able to use the formula function so that if the main

dimension changed, so did the others.

I notice in your example that there is only one dimension shown to control the group

diameters. Have I gone about this in the wrong way?

Also how is the PCD related to the bolt hole circle so that they are locked together

ie if the PCD is changed, so do all the bolt holes in your example?

The formula calculation assigns arbitary values ie v1019 can these be renamed to

meaningful values?

The angular function is nice as is the rotation from 0 degrees. One point I noticed

that changing the value from zero and then back to zero was that it would not accept

a zero degree value?

Relating back to an earlier question you asked re my origin points. These are used

so that all the holes are established in a positive X Y direction on my mill. No

DRO.

Regards

Geoff

"Ricky Black"

>Geoff,

>Look at this example.

>Start modifying the dimensions to see how it all stays tied together.

>

>There is a single dimension to modify the diameter of all the holes. They

>

>are all equal to eachother.

>The linear dimensions will reposition the center of the bolt hole circle and

>

>the holes adjust accordingly.

>The 100mmm dimension changes the diameter of the bolt hole circle and the

>

>holes adjust accordingly.

>The 0 degree angular dimension will rotate all the holes around the bolt

>hole circle.

>The black 72 diameter dimension will change the angular spacing between the

>

>holes.

>

>If you have any questions, please ask.

>

>Regards,

>Rick B.

>

>

>

2 REPLIES

N/A

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

12-15-2008 10:28 AM

Look at the attachment. The key to making this work is relationships.

Make sure Maintain Relationships is turned on. Make sure Relationship

Handles are turned on.

In this example I drew the large circle. I started the smaller circle by

locating the edge of the larger circle and clicked on it for the center of

the smaller circle. It places a connect relationship to tie the center of

the smaller circle to the larger one. If you change the position or diameter

of the larger circle, the smaller one will move accordingly.

The circular pattern command will not addd the relationships for you. It

simply creates a curcular grouped pattern.

When you drop the group, you can connect the centers of the smaller circles

to the edge of the larger circle. In V100 use the connect command under the

relate command group. Run the connect command. Locate the center of a

smaller corcle by moving the mouse over one of the circles. The circle will

highlight. Key in 'c' for center. It will find the circle center. Then click

on the larger circle. A connect relationship will be placed that ties the

center of the small circle to the edge of the large circle.

I hope this helps.

Regards,

Rick B.

N/A

- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content

12-24-2008 06:20 AM

Hi Ricky

I am getting the hang of it now.

Many thanks for your excellent guidance.

Have a Great Christmas

Kind Regards

Geoff

"Ricky Black"

>Geoff,

>Look at the attachment. The key to making this work is relationships.

>Make sure Maintain Relationships is turned on. Make sure Relationship

>Handles are turned on.

>In this example I drew the large circle. I started the smaller circle by

>locating the edge of the larger circle and clicked on it for the center of

>

>the smaller circle. It places a connect relationship to tie the center of

>

>the smaller circle to the larger one. If you change the position or diameter

>

>of the larger circle, the smaller one will move accordingly.

>

>The circular pattern command will not addd the relationships for you. It

>simply creates a curcular grouped pattern.

>When you drop the group, you can connect the centers of the smaller circles

>

>to the edge of the larger circle. In V100 use the connect command under the

>

>relate command group. Run the connect command. Locate the center of a

>smaller corcle by moving the mouse over one of the circles. The circle will

>

>highlight. Key in 'c' for center. It will find the circle center. Then click

>

>on the larger circle. A connect relationship will be placed that ties the

>

>center of the small circle to the edge of the large circle.

>

>I hope this helps.

>Regards,

>Rick B.

>

>

>

Follow Siemens PLM Software

© 2018 Siemens Product Lifecycle Management Software Inc